ГОСУДАРСТВЕННЫЙ СТАНДАРТ СОЮЗА ССР

ИЗДЕЛИЯ КРЕПЕЖНЫЕ

ТЕРМИНЫ И ОПРЕДЕЛЕНИЯ

ГОСТ 27017-86

(СТ СЭВ 6300-88)

ГОСУДАРСТВЕННЫЙ КОМИТЕТ СССР ПО УПРАВЛЕНИЮ
КАЧЕСТВОМ ПРОДУКЦИИ И СТАНДАРТАМ

Москва

ГОСУДАРСТВЕННЫЙ СТАНДАРТ СОЮЗА ССР

ИЗДЕЛИЯ КРЕПЕЖНЫЕ

Термины и определения

Fasteners. Terms and definitions

ГОСТ
27017-86

( СТ СЭВ 6300-88)

Дата введения 01.01.88

Настоящий стандарт устанавливает термины и определения основных понятий видов крепежных изделий общемашиностроительного применения, их конструктивных элементов.

Термины, установленные настоящим стандартом, обязательны для применения во всех видах документации и литературы, входящих в сферу действия стандартизации или использующих результаты этой деятельности.

Настоящий стандарт должен применяться совместно с ГОСТ 11708.

Для каждого понятия установлен один стандартизованный термин. Применение терминов - синонимов стандартизованного термина не допускается. Недопустимые к применению термины-синонимы приведены в стандарте в качестве справочных и обозначены пометой «Ндп».

Для отдельных стандартизованных терминов в стандарте приведены в качестве справочных краткие формы, которые разрешается применять в случаях, исключающих возможность их различного толкования.

Приведенные определения можно, при необходимости, изменять, вводя в них производные признаки, раскрывая значение используемых в них терминов, указывая объекты, входящие в объем определяемого понятия. Изменения не должны нарушать объем и содержание понятий, определенных в данном стандарте.

В стандарте в качестве справочных приведены иноязычные эквиваленты для ряда стандартизованных терминов на немецком ( D ), английском ( E ), французском ( F ) языках.

В стандарте приведены алфавитные указатели содержащихся в нем терминов на русском языке и их иноязычных эквивалентов.

Стандартизованные термины набраны полужирным шрифтом, их краткая форма - светлым, а недопустимые синонимы - курсивом.

В стандарте приведено приложение, содержащее терминологию и номенклатуру крепежных изделий на русском, немецком, английском и французском языках.

(Измененная редакция, Изм. № 1).

Термин

Определение

ОБЩИЕ ПОНЯТИЯ

1. Крепежное изделие

Деталь для образования соединения

E. Fastener

2. Болт

Крепежное изделие в форме стержня с наружной резьбой на одном конце, с головкой на другом, образующее соединение при помощи гайки или резьбового отверстия в одном из соединяемых изделий

D. Schraube

E. Bolt

F. Boulon

3. Винт

Крепежное изделие для образования соединения или фиксации, выполненное в форме стержня с наружной резьбой на одном конце и конструктивным элементом для передачи крутящего момента на другом.

D. Schraube

Е. Screw

F . Vis

Примечание . Конструктивный элемент винта для передачи крутящего момента может представлять головку со шлицем, головку с накаткой или, при отсутствии головки, шлиц в торце стержня

4. Шуруп

Крепежное изделие в форме стержня с наружной специальной резьбой, резьбовым коническим концом и головкой на другом конце, образующее резьбу в отверстии соединяемого деревянного или пластмассового изделия.

D. Holzschraube

Е. Wood screw

Примечание . Специальная резьба имеет треугольный заостренный профиль и большую ширину впадины по сравнению с шириной зуба

F. Vis à bois

5. Шпилька

Крепежное изделие в форме цилиндрического стержня с наружной резьбой на обоих концах или на всей длине стержня

D. Stiftschraube

Е. Stud

F. Goujon

6. Штифт

Крепежное изделие в форме цилиндрического или конического стержня для фиксации изделий при сборке

D. Stift

Е. Pin

F. Goupille

7. Гайка

Крепежное изделие с резьбовым отверстием конструктивным элементом для передачи крутящего момента.

D. Mutter

Е . Nut

Примечание . Конструктивным элементом гайки для передачи крутящего момента может быть многогранник, накатка на боковой поверхности, торцевые и радиальные отверстия, шлицы и т.д.

F. Ecrou

8. Шайба

Крепежное изделие с отверстием, подкладываемое под гайку или головку болта или винта для увеличения опорной поверхности и (или) предотвращения их самоотвинчивания

D. Scheibe

E. Washer

F. Rondelle

9. Шплинт

Крепежное изделие в форме проволочного стержня полукруглого сечения, сложенного вдвое с образованием головки

D. Splint

Е. Split pin

F. Goupille

10. Заклепка

Крепежное изделие в форме гладкого цилиндрического стержня с головкой на одном конце, служащее для получения неразъемного соединения за счет образования головки на другом конце стержня пластической деформацией

D. Niet

Е. Rivet

F . Rivet

ВИДЫ КРЕПЕЖНЫХ ИЗДЕЛИЙ

11. Ступенчатый болт

Болт, диаметр гладкой части стержня которого превышает номинальный диаметр резьбы

D. Schraube rnit Ansatzschaft

Е. Shoulder bolt

F. Corps de boulon renforcée

12. Откидной болт

Болт, головка которого выполнена в виде подвижной части шарнирного соединения

D. Augenschraube

Е. Eye bolt

F. Corps de boulon à oeil

13. Призонный болт

Болт, диаметр гладкой части стержня которого определяют из условия обеспечения работы соединения на срез

Ндп. Болт для отверстий из-под развертки

D. Paßschraube

Е. Fit bolt

F. Corps de boulon ajustable

14. Фундаментный болт

Болт, со специальной формой головки, служащий для крепления оборудования к фундаменту.

D. Steinschraube

Е. Foundation holt

Примечание . Специальная форма головки может представлять раздвинутые лапки прорезной части стержня, отогнутую часть стержня и т.д.

F. Tige de scellement

15. Невыпадающий винт

Винт, диаметр гладкой части стержня которого меньше внутреннего диаметра резьбы

D. Schraube mit Dehnschaft

Е. Screw with waisted shank

F. Vis à tige allégée

16. Самонарезающий винт

Винт, образующий специальную резьбу в отверстии одного из соединяемых пластмассовых или металлических изделий

D. Blechschraube

Е. Self-tapping screw

F. Vis à tôle

17. Самосверлящий самонарезающий винт

Самонарезающий винт с концом формы сверла

18. Установочный винт

Винт с концом специальной формы, служащий для фиксации изделий относительно друг друга

Е. Set screw

Примечание . Специальная форма конца может быть цилиндрической, конической, плоской и т.д.

19. Пружинный штифт

Цилиндрический штифт трубчатого сечения с продольным пазом по его длине, свернутой из пружинной стали

20. Прорезная гайка

Шестигранная гайка с радиально расположенными прорезями под шплинт со стороны одной из торцевых поверхностей

D. Kronenmutter

E. Hexagon slotted nut

F. Ecrou hexagonal à créneaux

21. Корончатая гайка

Шестигранная гайка, часть которой выполнена в виде цилиндра с радиально расположенными прорезями под шплинт

D. Kronenmutter

Е. Hexagon castle nut

F. Ecrou hexagonal à créneaux dégagés

22. Колпачковая гайка

Гайка, со сферической и плоской торцевой поверхностями и глухим резьбовым отверстием

D. Hutmutter

Е. Acorn nut

F. Ecrou borgne à calotte

23. Гайка-барашек

Гайка с плоскими выступающими элементами для передачи крутящего момента

D. Flügelmutter

Е. Wing nut

F. Ecrou à oreilles

24. Плоская шайба

Шайба с плоской опорной поверхностью

D. Scheibe

Е. Plain washer

F. Rondelle plate

25. Пружинная шайба

Разрезная круглая шайба, концы которой расположены в разных плоскостях, служащая для предотвращения самоотвинчивания крепежных изделий при ее упругой деформации под нагрузкой

Ндп. Шайба Гровера

D. Federring

E. Spring washer

F. Rondelle élastique

26. Стопорная шайба

Шайба, служащая для предотвращения самоотвинчивания крепежных изделий при помощи конструктивных элементов.

D. Scheibe mit Lappen oder Nasen

Е. Tab washer

Примечание . Конструктивными элементами шайбы являются лапки, носки, зубья и т.д.

F. Frein d’écrou

27. Пустотелая заклепка

Заклепка со стержнем трубчатого сечения

28. Полупустотелая заклепка

Заклепка, концевая часть стержня которой имеет трубчатое сечение

ЭЛЕМЕНТЫ КРЕПЕЖНЫХ ИЗДЕЛИЙ

29. Стержень крепежного изделия

Часть крепежного изделия, непосредственно входящая в отверстия соединяемых изделий или ввертываемая в материал одного из них

Стержень

30. Головка крепежного изделия

Часть крепежного изделия, имеющего стержень, служащая для передачи крутящего момента и (или) образования опорной поверхности

Головка

D . Kopf

E. Head

F. Tête

31. Подголовок болта

Гладкая часть стержня болта цилиндрической, овальной или квадратной формы, непосредственно примыкающая к головке и служащая для центрирования болта или предотвращения его проворачивания

Подголовок

D . Ansatz

E. Neck

F. Collet

32. Бурт крепежного изделия

Выступ на опорной поверхности многогранной гайки, головки болта или винта, выполненный в форме цилиндра или усеченного конуса диаметром, бóльшим диаметра их описанной окружности

Бурт

Ндп. Фланец

D. Bund

E. Collar

F . Embase

33. Опорный выступ крепежного изделия

Кольцевой выступ на опорной поверхности многогранной гайки или головки болта, диаметр которого меньше размера под ключ.

Опорный выступ

Примечание . Под размером под ключ понимается расстояние между противоположными гранями многогранной гайки или головки болта, винта, измеренное в плоскости, нормальной к их оси

Ндп. Опорная шайба

« Мертвая шайба »

D. Telleransatz

E. Washer face

F . Collerette

34. Шлиц крепежного изделия

Углубление специальной формы в торце головки болта, винта или шурупа, в торце установочного винта без головки, вдоль образующей или в торце гайки

Шлиц

Примечание . Форма шлица может быть шестигранной, крестообразной, в виде сквозной или несквозной прорези и т.д.

35. Шип болта

Выступ на опорной поверхности головки болта, служащий для предотвращения его проворачивания

Шип

36. Ус болта

Выступ на опорной поверхности головки и стержня болта, служащий для предотвращения его проворачивания

Ус

D. Nase

E. Nib

F. Ergot

37. Буравчик

Резьбовой конической конец шурупа, служащий для нарезания резьбы в деревянном или пластмассовом изделии при образовании соединения

E. Gimlet point

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА РУССКОМ ЯЗЫКЕ

Болт                                                                                                                                2

Болт для отверстий из-под развертки                                                                    13

Болт откидной                                                                                                            12

Болт призонный                                                                                                        13

Болт ступенчатый                                                                                                     11

Болт фундаментный                                                                                                 14

Буравчик                                                                                                                     37

Бурт                                                                                                                               32

Бурт крепежного изделия                                                                                        32

Винт                                                                                                                                3

Винт невыпадающий                                                                                               15

Винт самонарезающий                                                                                             16

Винт самонарезающий самосверлящий                                                               17

Винт установочный                                                                                                  18

Выступ крепежного изделия опорный                                                                 33

Выступ опорный                                                                                                          33

Гайка                                                                                                                             7

Гайка-барашек                                                                                                          23

Гайка колпачковая                                                                                                  22

Гайка корончатая                                                                                                     21

Гайка прорезная                                                                                                        20

Головка                                                                                                                         30

Головка крепежного изделия                                                                                 30

Заклепка                                                                                                                     10

Заклепка полупустотелая                                                                                       28

Заклепка пустотелая                                                                                                27

Изделие крепежное                                                                                                    1

Подголовок                                                                                                                   31

Подголовок болта                                                                                                      31

Стержень                                                                                                                      29

Стержень крепежного изделия                                                                              29

Ус                                                                                                                                  36

Ус болта                                                                                                                       36

Фланец                                                                                                                          32

Шайба                                                                                                                            8

Шайба Гровера                                                                                                            25

Шайба «мертвая»                                                                                                       33

Шайба опорная                                                                                                            33

Шайба плоская                                                                                                          24

Шайба пружинная                                                                                                    25

Шайба стопорная                                                                                                       26

Шип                                                                                                                              35

Шип болта                                                                                                                   35

Шлиц                                                                                                                            34

Шлиц крепежного изделия                                                                                     34

Шпилька                                                                                                                       5

Шплинт                                                                                                                         9

Штифт                                                                                                                            6

Штифт пружинный                                                                                                   19

Шуруп                                                                                                                            4

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА НЕМЕЦКОМ ЯЗЫКЕ

Ansatz                                                                                                                            31

Augenschraube                                                                                                               12

Blechschraube                                                                                                                16

Bund                                                                                                                               32

Federring                                                                                                                       25

Flügelmulter                                                                                                                   23

Holzschraube                                                                                                                   4

Hutmutter                                                                                                                       22

Kopf                                                                                                                               30

Kronenmutte                                                                                                             20, 21

Mutter                                                                                                                              7

Nase                                                                                                                               36

Niet                                                                                                                                10

Paßschraube                                                                                                                   13

Scheibe                                                                                                                      8, 24

Scheibe mit Lappen oder Nasen                                                                                     26

Schraube                                                                                                                      2, 3

Schraube mit Ansatzschaft                                                                                             11

Schraube mit Dehnschaft                                                                                                15

Splint                                                                                                                               9

Steinschraube                                                                                                                 14

Stift                                                                                                                                  6

Stiftschraube                                                                                                                    5

Telleransatz                                                                                                                   33

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА АНГЛИЙСКОМ ЯЗЫКЕ

Acorn nut                                                                                                                       22

Bolt                                                                                                                                  2

Collar                                                                                                                             32

Eye bolt                                                                                                                          12

Fastener                                                                                                                           1

Fit bolt                                                                                                                           13

Foundation bolt                                                                                                              14

Gimlet point                                                                                                                   37

Head                                                                                                                              30

Hexagon castle nut                                                                                                         21

Hexagon slotted nut                                                                                                        20

Neck                                                                                                                               31

Nib                                                                                                                                 36

Nut                                                                                                                                   7

Pin                                                                                                                                    6

Plain washer                                                                                                                  24

Rivet                                                                                                                              10

Screw                                                                                                                               3

Screw with waisted shank                                                                                             15

Self-tapping screw                                                                                                         16

Set screw                                                                                                                       18

Shoulder bolt                                                                                                                 11

Split pin                                                                                                                           9

Spring washer                                                                                                                25

Stud                                                                                                                                  5

Tab washer                                                                                                                    26

Washer                                                                                                                             8

Washer face                                                                                                                   33

Wing nut                                                                                                                         23

Wood screw                                                                                                                     4

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА ФРАНЦУЗСКОМ ЯЗЫКЕ

Boulon                                                                                                                             2

Collerette                                                                                                                       33

Collet                                                                                                                             31

Corps de boulon ajustable                                                                                             13

Corps de boulon à oeil                                                                                                   12

Corps de boulon renforcée                                                                                             11

Ecrou                                                                                                                               7

Ecrou à oreilles                                                                                                             23

Ecrou borgne á calotte                                                                                                   22

Ecrou hexagonal à créneaux                                                                                           20

Ecrou hexagonal à créneaux dégagés                                                                             21

Embase                                                                                                                          32

Ergot                                                                                                                              36

Frein d’écrou                                                                                                                 26

Goujon                                                                                                                             5

Goupille                                                                                                                       6, 9

Rivet                                                                                                                              10

Rondelle                                                                                                                          8

Rondelle élastique                                                                                                         25

Rondelle plate                                                                                                                24

Tête                                                                                                                                30

Tige de scellement                                                                                                         14

Vis                                                                                                                                   3

Vis à bois                                                                                                                         4

Vis à tige allégée                                                                                                           15

Vis à tôle                                                                                                                        16

ПРИЛОЖЕНИЕ

Справочное

ТЕРМИНОЛОГИЯ И НОМЕНКЛАТУРА КРЕПЕЖНЫХ ИЗДЕЛИЙ НА РУССКОМ, НЕМЕЦКОМ, АНГЛИЙСКОМ И ФРАНЦУЗСКОМ ЯЗЫКАХ

I. ТЕРМИНОЛОГИЯ И НОМЕНКЛАТУРА КРЕПЕЖНЫХ ИЗДЕЛИЙ

1. РЕЗЬБА

Наименование

Чертеж

1.1. Резьба

1.2. Коническая резьба

1.3. Самонарезающая резьба

1.4. Шурупная резьба

1. 5 . Метрическая резьба

1.6. Метрическая резьба с мелким шагом

2. ФОРМЫ ГОЛОВОК

Наименование

Чертеж

2.1. Шестигранная головка

2.2. Шестигранная головка с опорным выступом

2.3. Шестигранная головка с цилиндрическим буртом

2.4. Шестигранная головка с фланцем

2.5. Квадратная головка

2.6. Квадратная головка с цилиндрическим буртом

2.7. Трехгранная головка с цилиндрическим буртом

2.8. Восьмигранная головка

2.9. Двенадцатигранная головка с фланцем

2.10. Т-образная головка

2.11. Т-образная головка с квадратным подголовком

2.12. Полукруглая головка

2.13. Низкая полукруглая головка

2.14. Полукруглая головка с усом

2.15. Низкая полукруглая головка с квадратным подголовком

2.16. Полукруглая головка с овальным подголовком

2.17. Цилиндрическая головка

2.18. Цилиндрическая головка со сферой

2.19. Низкая цилиндрическая головка со сферой

2.20. Цилиндрическая скругленная головка

2.21. Потайная головка

2.22. Потайная головка с заплечиком

2.23. Потайная головка с усом

2.24. Потайная головка с квадратным подголовком

2.25. Полупотайная головка

2.26. Полупотайная головка с заплечиком

2.27. Рифленая цилиндрическая головка с прямым рифлением

2.28. Рифленая цилиндрическая головка с сетчатым рифлением

3. ФОРМЫ СТЕРЖНЕЙ

Наименование

Чертеж

3.1. Нормальный стержень (стержень, диаметр которого равен номинальному диаметру резьбы)

3.2. Уменьшенный стержень (стержень, диаметр которого приблизительно равен среднему диаметру резьбы)

3.3. Увеличенный стержень, диаметр которого больше номинального диаметра резьбы

3.4. Утоненный стержень (стержень, диаметр которого меньше внутреннего диаметра резьбы)

3.5. Ступенчатый стержень

3.6. Пустотелый стержень

3.7. Полупустотелый стержень

4. КОНЦЫ БОЛТОВ И ВИНТОВ

Наименование

Чертеж

4.1. Конец без фаски

4.2. Сферический конец

4.3. Конец с фаской

4.4. Конический конец

4.5. Конический притупленный конец

4.6. Засверленный конец

4.7. Плоский конец

4.8. Цилиндрический конец

4.9. Цилиндрический укороченный конец

4.10. Ступенчатый конец со сферой

4.11. Ступенчатый конец с конусом

4.12. Конический с притуплением конец самонарезающего винта с режущей кромкой

4.13. Конический конец самонарезающего винта

4.14. Плоский конец самонарезающего винта

4.15. Конец резьбовыдавливающего винта

4.16. Буравчик шурупа

5. ЭЛЕМЕНТЫ, ПЕРЕДАЮЩИЕ ВРАЩЕНИЕ

Наименование

Чертеж

5.1. Шестигранник

5.2. Квадрат

5.3. Трехгранник

5.4. Восьмигранник

5.5. Двенадцатигранник

5.6. Трехгранное углубление

5.7. Квадратное углубление

5.8. Шестигранное углубление

5.9. Шлицевое углубление

5.10. Зубчатое углубление

5.11. Прямой шлиц

5.12. Крестообразный шлиц

5.13. Барашек

5.14. Прямое рифление

5.15. Сетчатое рифление

5.16. Накрест расположенные отверстия

6. БОЛТЫ И ВИНТЫ С ШЕСТИГРАННОЙ ГОЛОВКОЙ

Наименование

Чертеж

6.1. Болт с шестигранной головкой

6.2. Ступенчатый болт с шестигранной головкой

6.3. Установочный винт с шестигранной головкой и цилиндрическим концом

6.4. Установочный винт с шестигранной головкой и ступенчатым концом с конусом

6.5. Винт с шестигранной головкой и утоненным стержнем

6.6. Болт с шестигранной головкой с цилиндрическим буртом

6.7. Болт с шестигранной головкой с фланцем

7. ВИНТЫ С ЧЕТЫРЕХГРАННОЙ (КВАДРАТНОЙ) ГОЛОВКОЙ

Наименование

Чертеж

7.1. Винт с квадратной головкой

7.2. Винт с квадратной головкой с цилиндрическим буртом

7.3. Установочный винт с квадратной головкой и цилиндрическим концом

7.4. Установочный винт с квадратной головкой и засверленным концом

7.5. Установочный винт с квадратной головкой с цилиндрическим буртом и ступенчатым концом со сферой

8. БОЛТЫ С ТРЕХГРАННОЙ ГОЛОВКОЙ

Наименование

Чертеж

8. Болт с трехгранной головкой с цилиндрическим буртом

9. БОЛТЫ С ВОСЬМИГРАННОЙ ГОЛОВКОЙ

Наименование

Чертеж

9. Болт с восьмигранной головкой

10. БОЛТЫ С ДВЕНАДЦАТИГРАННОЙ ГОЛОВКОЙ

Наименование

Чертеж

10. Болт с двенадцатигранной головкой с фланцем

11. БОЛТЫ С Т-ОБРАЗНОЙ ГОЛОВКОЙ

Наименование

Чертеж

11.1. Болт с Т-образной головкой

11.2. Болт с Т-образной головкой и квадратным подголовком

11.3. Болт с Т-образной головкой и выступами под головкой

12. БОЛТЫ С ПОЛУКРУГЛОЙ ГОЛОВКОЙ

Наименование

Чертеж

12.1. Болты с низкой полукруглой головкой и квадратным подголовком

12.2. Болт с полукруглой головкой и усом

12.3. Болт с низкой полукруглой головкой и усом

12.4. Болт с полукруглой головкой и овальным подголовком

13. БОЛТЫ С ПОТАЙНЫМИ ГОЛОВКАМИ

Наименование

Чертеж

13.1. Болт с потайной головкой и квадратным подголовком

13.2. Болт с потайной головкой и усом

13.3. Шинный болт

14. ВИНТЫ С ВНУТРЕННИМ ШЕСТИГРАННИКОМ

Наименование

Чертеж

14.1. Винт с цилиндрической головкой и шестигранным углублением под ключ

14.2. Ступенчатый винт с цилиндрической головкой и шестигранным углублением под ключ

14.3. Винт с потайной головкой и шестигранным углублением под ключ

15. ВИНТЫ С ПРЯМЫМ ШЛИЦЕМ

Наименование

Чертеж

15.1. Винт с цилиндрической головкой

15.2. Винт с цилиндрической скругленной головкой

15.3. Винт с цилиндрической головкой со сферой

15.4. Установочный винт с цилиндрической головкой со сферой и цилиндрическим концом

15.5. Ступенчатый винт с цилиндрической головкой со сферой

15.6. Винт с цилиндрической головкой со сферой, с отверстием в головке

15.7. Винт с уменьшенной цилиндрической головкой со сферой

15.8. Винт с потайной головкой

15.9. Установочный винт с потайной головкой и цилиндрическим концом

15.10. Винт с полупотайной головкой

15.11. Установочный винт с полупотайной головкой и цилиндрическим концом

15.12. Винт с потайной головкой и прямым закрытым шлицем

15.13. Винт с полукруглой головкой

16. ВИНТЫ С КРЕСТООБРАЗНЫМ ШЛИЦЕМ

Наименование

Чертеж

16.1. Винт с цилиндрической головкой со сферой и крестообразным шлицем

16.2. Винт с потайной головкой и крестообразным шлицем

16.3. Винт с полупотайной головкой и крестообразным шлицем

16.4. Винт с полукруглой головкой и крестообразным шлицем

17. ВИНТЫ С НЕВЫПАДАЮЩИМИ ДЕТАЛЯМИ

Наименование

Чертеж

17.1. Винт с шестигранной головкой с невыпадающей плоской шайбой

17.2. Винт с шестигранной головкой с невыпадающими пружинной и плоской шайбами

17.3. Винт с цилиндрической головкой со сферой и невыпадающей пружинной шайбой

17.4. Винт с полупотайной головкой и невыпадающей стопорной шайбой

18. РАЗЛИЧНЫЕ ТИПЫ БОЛТОВ И ВИНТОВ

Наименование

Чертеж

18.1. Откидной болт

18.2. Болт с низкой полукруглой головкой и шипом

18.3. Болт с плоской головкой и шипом

18.4. Болт с потайной головкой и двумя шипами

18.5. Костыльковый болт

18.6. Болт с колпачковой головкой

18.7. Конический болт

18.8. Анкерный болт

18.9. Фундаментный болт

18.10. Винт-барашек

18.11. Рым-болт

19. УСТАНОВОЧНЫЕ ВИНТЫ БЕЗ ГОЛОВОК

Наименование

Чертеж

19.1. Установочный винт с плоским концом

19.2. Установочный винт с цилиндрическим концом

19.3. Установочный винт с засверленным концом

19.4. Установочный винт с коническим концом

19.5. Установочный винт с плоским концом и шестигранным углублением под ключ

19.6. Установочный винт с цилиндрическим концом и шестигранным углублением под ключ

19.7. Установочный винт с засверленным концом и шестигранным углублением под ключ

19.8. Установочный винт с коническим концом и шестигранным углублением под ключ

20. САМОНАРЕЗАЮЩИЕ ВИНТЫ

Наименование

Чертеж

20.1. Самонарезающий винт с шестигранной головкой

20.2. Самонарезающий винт с цилиндрической головкой

20.3. Самонарезающий винт с потайной головкой

20.4. Самонарезающий винт с полупотайной головкой

20.5. Самонарезающий винт с потайной головкой и крестообразным шлицем

20.6. Самонарезающий винт с полупотайной головкой и крестообразным шлицем

20.7. Самонарезающий винт с цилиндрической скругленной головкой и крестообразным шлицем

21. ШУРУПЫ

Наименование

Чертеж

21.1. Шуруп с шестигранной головкой

21.2. Шуруп с квадратной головкой

21.3. Шуруп с полукруглой головкой

21.4. Шуруп с полупотайной головкой

21.5. Шуруп с потайной головкой

21.6. Шуруп с полукруглой головкой и крестообразным шлицем

21.7. Шуруп с полупотайной головкой и крестообразным шлицем

21.8. Шуруп с потайной головкой и крестообразным шлицем

22. РЕЗЬБОНАРЕЗАЮЩИЕ ВИНТЫ

Наименование

Чертеж

22.1. Резьбонарезающий винт с шестигранной головкой

22.2. Резьбонарезающий винт с цилиндрической головкой

22.3. Резьбонарезающий винт с потайной головкой

22.4. Резьбонарезающий винт с полупотайной головкой

22.5. Резьбонарезающий винт с цилиндрической головкой со сферой и крестообразным шлицем

22.6. Резьбонарезающий винт с потайной головкой и крестообразным шлицем

22.7. Резьбонарезающий винт с полупотайной головкой и крестообразным шлицем

23. РЕЗЬБОВЫДАВЛИВАЮЩИЕ ВИНТЫ

Наименование

Чертеж

23. Резьбовыдавливающий винт

24. ВИНТЫ С РИФЛЕНОЙ ГОЛОВКОЙ

Наименование

Чертеж

24.1. Винт с рифленой цилиндрической головкой и плоским концом

24.2. Винт с рифленой цилиндрической головкой и коническим концом

24.3. Винт с рифленой цилиндрической головкой и ступенчатым концом с конусом

24.4. Винт с рифленой цилиндрической головкой и засверленным концом

24.5. Винт с рифленой цилиндрической головкой и сферическим концом

24.6. Винт с рифленой цилиндрической головкой и цилиндрическим концом

25. ШТИФТЫ

Наименование

Чертеж

25.1. Цилиндрический штифт

25.2. Цилиндрический штифт с внутренней резьбой

25.3. Цилиндрический штифт с засверленными концами

25.4. Цилиндрический насеченный штифт

25.5. Цилиндрический насеченный штифт с коническими насечками

25.6. Конический разводной штифт

25.7. Конический штифт

25.8. Конический штифт с внутренней резьбой

25.9. Конический штифт с резьбовой цапфой

25.10. Пружинный штифт

25.11. Резьбовой штифт с плоским концом и шлицем

25.12. Резьбовой штифт с плоским концом и шестигранным углублением под ключ

25.13. Резьбовой штифт с коническим притупленным концом и шестигранным углублением под ключ

25.14. Резьбовой штифт с цилиндрическим концом и шестигранным углублением под ключ.

25.15. Резьбовой штифт с засверленным концом и шестигранным углублением под ключ

26. ШПИЛЬКИ

Наименование

Чертеж

26.1. Шпилька

26.2. Шпилька с утоненным стержнем

26.3. Шпилька с резьбой по всей длине

26.4. Приварная шпилька

26.5. Стяжная шпилька с проточками и шестигранным хвостовиком

27. ЗАКЛЕПКИ

Наименование

Чертеж

27.1. Заклепка с полукруглой головкой

27.2. Заклепка с полукруглой низкой головкой

27.3. Заклепка с потайной головкой

27.4. Заклепка с полупотайной головкой

27.5. Заклепка с полупотайной низкой головкой

27.6. Заклепка с плоской головкой

27.7. Пустотелая заклепка со скругленной головкой

27.8. Пустотелая заклепка с плоской головкой

27.9. Пустотелая заклепка с потайной головкой

27.10. Пустотелая заклепка с плоской головкой

27.11. Пустотелая заклепка с потайной головкой

27.12. Полупустотелая заклепка с полукруглой головкой

28. ГАЙКИ

Наименование

Чертеж

28.1. Шестигранная гайка

28.2. Шестигранная низкая гайка

28.3. Шестигранная гайка с цилиндрическим буртом

28.4. Шестигранная гайка с фланцем

28.5. Шестигранная гайка с опорной шайбой

28.6. Шестигранная приварная гайка

28.7. Квадратная гайка

28.8. Квадратная низкая гайка

28.9. Анкерная гайка

28.10. Квадратная гайка с цилиндрическим буртом

28.11. Квадратная приварная гайка

28.12. Трехгранная гайка с цилиндрическим буртом

28.13. Восьмигранная гайка

28.14. Двенадцатигранная гайка с фланцем

28.15. Самоконтрящаяся гайка с деформированной резьбой

28.16. Самоконтрящаяся гайка с кольцевой вставкой из полимера

28.17. Шестигранная прорезная гайка

28.18. Шестигранная корончатая гайка

28.19. Шестигранная низкая корончатая гайка

28.20. Колпачковая гайка

28.21. Рифленая гайка

28.22. Круглая гайка со шлицем на торце

28.23. Шлицевая гайка

28.24. Круглая гайка с радиально расположенными отверстиями

28.25. Круглая гайка с отверстиями на торце под ключ

28.26. Гайка-барашек

29. ШАЙБЫ

Наименование

Чертеж

29.1. Круглая плоская шайба

29.2. Квадратная шайба

29.3. Круглая шайба с квадратным отверстием

29.4. Косая шайба

29.5. Пружинная шайба

29.6. Пружинная шайба с отогнутыми концами

29.7. Пружинная двухвитковая шайба

29.8. Пружинная изогнутая шайба

29.9. Стопорная шайба с наружными зубьями

29.10. Стопорная шайба с внутренними зубьями

29.11. Стопорная шайба с зубьями под винты с потайной и полупотайной головкой

29.12. Пружинная волнистая шайба

29.13. Пружинная шайба с наружными зубьями

29.14. Пружинная шайба с внутренними зубьями

29.15. Пружинная шайба с зубьями под винты с потайной и полупотайной головкой

29.16. Стопорная шайба с двумя лапками

29.17. Стопорная шайба с наружным носком

29.18. Стопорная шайба с лапкой

29.19. Стопорная шайба с внутренним носком

30. ШПЛИНТЫ

Наименование

Чертеж

30. Шплинт

II. АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ И НАИМЕНОВАНИЙ КРЕПЕЖНЫХ ИЗДЕЛИЙ НА РУССКОМ ЯЗЫКЕ

Барашек                                                                                                                           5.13

Болт анкерный                                                                                                               18.8

Болт конический                                                                                                            18.7

Болт костыльковый                                                                                                        18.5

Болт откидной                                                                                                                18.1

Болт с восьмигранной головкой                                                                                   9

Болт с двенадцатигранной головкой с фланцем                                                        10

Болт с колпачковой головкой                                                                                       18.6

Болт с низкой полукруглой головкой и квадратным подголовком                          12.1

Болт с низкой полукруглой головкой и усом                                                              12.3

Болт с низкой полукруглой головкой и шипом                                                          18.2

Болт с плоской головкой и шипом                                                                               18.3

Болт с полукруглой головкой и овальным подголовком                                           12.4

Болт с полукруглой головкой и усом                                                                           12.2

Болт с потайной головкой и квадратным подголовком                                            13.1

Болт с потайной головкой и двумя шипами                                                               18.4

Болт с потайной головкой и усом                                                                                13.2

Болт с Т-образной головкой                                                                                         11.1

Болт с Т-образной головкой и выступами под головкой                                           11.3

Болт с Т-образной головкой и квадратным подголовком                                         11.2

Болт с трехгранной головкой с цилиндрическим буртом                                         8

Болт ступенчатый с шестигранной головкой                                                             6.2

Болт с шестигранной головкой                                                                                    6.1

Болт с шестигранной головкой с фланцем                                                                 6.7

Болт с шестигранной головкой с цилиндрическим буртом                                      6.6

Болт фундаментный                                                                                                      18.9

Болт шинный                                                                                                                  13.3

Буравчик шурупа                                                                                                            4.16

Винт-барашек                                                                                                                                              18.10

Винт резьбовыдавливающий                                                                                        23

Винт резьбовыдавливающий с полупотайной головкой                                           22.4

Винт резьбонарезающий с полупотайной головкой и крестообразным шлицем   22.7

Винт резьбонарезающий с потайной головкой                                                          22.3

Винт резьбонарезающий с потайной головкой и крестообразным шлицем           22.6

Винт резьбонарезающий с цилиндрической головкой                                              22.2

Винт резьбонарезающий с цилиндрической головкой со сферой и крестообразным шлицем                                                                                                                                   22.5

Винт резьбонарезающий с шестигранной головкой                                                  22.1

Винт самонарезающий с полупотайной головкой                                                     20.4

Винт самонарезающий с полупотайной головкой и крестообразным шлицем      20.6

Винт самонарезающий с потайной головкой                                                             20.3

Винт самонарезающий с потайной головкой и крестообразным шлицем              20.5

Винт самонарезающий с цилиндрической головкой                                                 20.2

Винт самонарезающий с цилиндрической скругленной головкой и крестообразным шлицем                                                                                                                                  20.7

Винт самонарезающий с шестигранной головкой                                                     20.1

Винт с квадратной головкой                                                                                        7.1

Винт с квадратной головкой с цилиндрическим буртом                                          7.2

Винт с полукруглой головкой                                                                                                                                              15.13

Винт с полукруглой головкой и крестообразным шлицем                                       16.4

Винт с полупотайной головкой                                                                                                                                              15.10

Винт с полупотайной головкой и крестообразным шлицем                                     16.3

Винт с полупотайной головкой и невыпадающей стопорной шайбой                    17.4

Винт с потайной головкой                                                                                            15.8

Винт с потайной головкой и крестообразным шлицем                                             16.2

Винт с потайной головкой и прямым закрытым шлицем                                                                                                                                              15.12

Винт с потайной головкой и шестигранным углублением под ключ                      14.3

Винт с рифленой цилиндрической головкой и засверленным концом                   24.4

Винт с рифленой цилиндрической головкой и коническим концом                      24.2

Винт с рифленой цилиндрической головкой и плоским концом                            24.1

Винт с рифленой цилиндрической головкой и ступенчатым концом и конусом 24.3

Винт с рифленой цилиндрической головкой и сферическим концом                    24.5

Винт с рифленой цилиндрической головкой и цилиндрическим концом              24.6

Винт ступенчатый с цилиндрической головкой со сферой                                      15.5

Винт ступенчатый с цилиндрической головкой и шестигранным углублением под ключ                                                                                                                                14.2

Винт с уменьшенной цилиндрической головкой со сферой                                     15.7

Винт с цилиндрической головкой                                                                               15.1

Винт с цилиндрической головкой со сферой                                                             15.3

Винт с цилиндрической головкой со сферой и крестообразным шлицем              16.1

Винт с цилиндрической головкой со сферой и невыпадающей пружинной шайбой                                                                                                                                 17.3

Винт с цилиндрической головкой со сферой, с отверстием в головке                    15.6

Винт с цилиндрической головкой и шестигранным углублением под ключ          14.1

Винт с цилиндрической скругленной головкой                                                         15.2

Винт с шестигранной головкой с невыпадающей плоской шайбой                         17.1

Винт с шестигранной головкой с невыпадающими пружинной и плоской шайбами                                                                                                                                  17.2

Винт с шестигранной головкой и утоненным стержнем                                          6.5

Винт установочный с засверленным концом                                                             19.3

Винт установочный с засверленным концом и шестигранным углублением под ключ                                                                                                                                  19.7

Винт установочный с квадратной головкой и засверленным концом                     7.4

Винт установочный с квадратной головкой и цилиндрическим буртом и ступенчатым концом со сферой                                                                                                                                   7.5

Винт установочный с квадратной головкой и цилиндрическим концом                7.3

Винт установочный с коническим концом                                                                 19.4

Винт установочный с коническим концом и шестигранным углублением под ключ                                                                                                                                19.8

Винт установочный с плоским концом                                                                       19.1

Винт установочный с плоским концом и шестигранным углублением под ключ                                                                                                                               19.5

Винт установочный с полупотайной головкой и цилиндрическим концом                                                                                                                                              15.11

Винт установочный с потайной головкой и цилиндрическим концом                   15.9

Винт установочный с цилиндрическим концом                                                        19.2

Винт установочный с цилиндрическим концом и шестигранным углублением под ключ                                                                                                                                   19.6

Винт установочный с цилиндрической головкой со сферой и цилиндрическим концом                                                                                                                                      15.4

Винт установочный с шестигранной головкой и ступенчатым концом с конусом                                                                                                                                  6.4

Винт установочный с шестигранной головкой и цилиндрическим концом           6.3

Восьмигранник                                                                                                              5.4

Гайка анкерная                                                                                                              28.9

Гайка-барашек                                                                                                                                              28.26

Гайка восьмигранная                                                                                                                                              28.13

Гайка двенадцатигранная с фланцем                                                                                                                                              28.14

Гайка квадратная                                                                                                           28.7

Гайка квадратная низкая                                                                                              28.8

Гайка квадратная приварная                                                                                                                                              28.11

Гайка квадратная с цилиндрическим буртом                                                                                                                                              28.10

Гайка колпачковая                                                                                                                                              28.20

Гайка круглая с отверстиями на торце под ключ                                                                                                                                              28.25

Гайка круглая с радиально расположенными отверстиями                                                                                                                                              28.24

Гайка круглая со шлицем на торце                                                                                                                                              28.22

Гайка рифленая                                                                                                                                              28.21

Гайка самоконтрящаяся с деформированной резьбой                                                                                                                                              28.15

Гайка самоконтрящаяся с кольцевой вставкой из полимера                                                                                                                                              28.16

Гайка трехгранная с цилиндрическим буртом                                                                                                                                              28.12

Гайка шестигранная                                                                                                      28.1

Гайка шестигранная корончатая                                                                                                                                              28.18

Гайка шестигранная низкая                                                                                          28.2

Гайка шестигранная низкая корончатая                                                                                                                                              28.19

Гайка шестигранная приварная                                                                                   28.6

Гайка шестигранная прорезная                                                                                                                                              28.17

Гайка шестигранная с опорной шайбой                                                                      28.5

Гайка шестигранная с фланцем                                                                                   28.4

Гайка шестигранная с цилиндрическим буртом                                                        28.3

Гайка шлицевая                                                                                                                                              28.23

Головка восьмигранная                                                                                                 2.8

Головка двенадцатигранная с фланцем                                                                      2.9

Головка квадратная                                                                                                       2.5

Головка квадратная с цилиндрическим буртом                                                         2.6

Головка низкая полукруглая                                                                                         2.13

Головка низкая полукруглая с квадратным подголовком                                         2.15

Головка низкая цилиндрическая со сферой                                                               2.19

Головка полукруглая                                                                                                     2.12

Головка полукруглая с овальным подголовком                                                         2.16

Головка полукруглая с усом                                                                                         2.14

Головка полупотайная                                                                                                  2.25

Головка полупотайная с заплечиком                                                                          2.26

Головка потайная                                                                                                          2.21

Головка потайная с заплечиком                                                                                  2.22

Головка потайная с квадратным подголовком                                                           2.24

Головка потайная с усом                                                                                              2.23

Головка рифленая цилиндрическая с прямым рифлением                                       2.27

Головка рифленая цилиндрическая с сетчатым рифлением                                    2.28

Головка цилиндрическая со сферой                                                                            2.18

Головка Т-образная                                                                                                       2.10

Головка Т-образная с квадратным подголовком                                                        2.11

Головка трехгранная с цилиндрическим буртом                                                       2.7

Головка цилиндрическая                                                                                              2.17

Головка цилиндрическая скругленная                                                                        2.20

Головка шестигранная                                                                                                  2.1

Головка шестигранная с фланцем                                                                               2.4

Головка шестигранная с опорной шайбой                                                                  2.2

Головка шестигранная с цилиндрическим буртом                                                    2.3

Двенадцатигранник                                                                                                       5.5

Заклепка полупустотелая с плоской головкой                                                                                                                                              27.10

Заклепка полупустотелая с полукруглой головкой                                                                                                                                              27.12

Заклепка полупустотелая с потайной головкой                                                                                                                                              27.11

Заклепка с плоской головкой                                                                                       27.6

Заклепка с полукруглой головкой                                                                                27.1

Заклепка с полукруглой низкой головкой                                                                  27.2

Заклепка с полупотайной головкой                                                                             27.4

Заклепка с полупотайной низкой головкой                                                                27.5

Заклепка с потайной головкой                                                                                     27.3

Заклепка пустотелая с плоской головкой                                                                   27.8

Заклепка пустотелая с потайной головкой                                                                 27.9

Заклепка пустотелая со скругленной головкой                                                          27.7

Квадрат                                                                                                                           5.2

Конец без фаски                                                                                                             4.1

Конец засверленный                                                                                                      4.6

Конец конический                                                                                                         4.4

Конец конический притупленный                                                                               4.5

Конец плоский                                                                                                               4.7

Конец резьбовыдавливающего винта                                                                          4.15

Конец самонарезающего винта конический                                                               4.13

Конец самонарезающего винта конический с притуплением с режущей кромкой                                                                                                                                4.12

Конец самонарезающего винта плоский                                                                     4.14

Конец ступенчатый с конусом                                                                                     4.11

Конец ступенчатый со сферой                                                                                     4.10

Конец с фаской                                                                                                              4.3

Конец сферический                                                                                                       4.2

Конец цилиндрический                                                                                                4.8

Конец цилиндрический укороченный                                                                         4.9

Отверстия, накрест расположенные                                                                            5.16

Резьба                                                                                                                              1.1

Резьба коническая                                                                                                         1.2

Резьба метрическая                                                                                                       1.5

Резьба метрическая с мелким шагом                                                                           1.6

Резьба самонарезающая                                                                                                1.3

Резьба шурупная                                                                                                             1.4

Рифление прямое                                                                                                           5.14

Рифление сетчатое                                                                                                        5.15

Рым-болт                                                                                                                                              18.11

Стержень нормальный                                                                                                  3.1

Стержень полупустотелый                                                                                           3.7

Стержень пустотелый                                                                                                   3.6

Стержень ступенчатый                                                                                                 3.5

Стержень увеличенный                                                                                                 3.3

Стержень уменьшенный                                                                                               3.2

Стержень утоненный                                                                                                     3.4

Трехгранник                                                                                                                   5.3

Углубление квадратное                                                                                                 5.7

Углубление трехгранное                                                                                               5.8

Углубление шестигранное                                                                                            5.9

Шайба квадратная                                                                                                         29.2

Шайба косая                                                                                                                   29.4

Шайба круглая с квадратным отверстием                                                                  29.3

Шайба круглая плоская                                                                                                 29.1

Шайба пружинная                                                                                                         29.5

Шайба пружинная волнистая                                                                                                                                              29.12

Шайба пружинная двухвитковая                                                                                  29.7

Шайба пружинная изогнутая                                                                                        29.8

Шайба пружинная с отогнутыми концами                                                                 29.6

Шайба пружинная с внутренними зубьями                                                                                                                                              29.14

Шайба пружинная с зубьями под винты с потайной и полупотайной головкой                                                                                                                                              29.15

Шайба пружинная с наружными зубьями                                                                                                                                              29.13

Шайба стопорная с внутренними зубьями                                                                                                                                              29.10

Шайба стопорная с внутренним носком                                                                                                                                              29.19

Шайба стопорная с двумя лапками                                                                                                                                              29.16

Шайба стопорная с зубьями под винты с потайной и полупотайной головками                                                                                                                                     29.11

Шайба стопорная с лапкой                                                                                                                                              29.18

Шайба стопорная с наружными зубьями                                                                    19.9

Шайба стопорная с наружным носком                                                                                                                                              29.17

Шестигранник                                                                                                                5.1

Шлиц крестообразный                                                                                                  5.12

Шлиц прямой                                                                                                                 5.11

Шпилька                                                                                                                         26.1

Шпилька приварная                                                                                                      26.4

Шпилька с резьбой по всей длине                                                                               26.3

Шпилька стяжная с проточками и шестигранным хвостовиком                             26.5

Шпилька с утоненным стержнем                                                                                26.2

Шплинт                                                                                                                           30

Штифт конический                                                                                                       25.7

Штифт конический разводной                                                                                     25.6

Штифт конический с внутренней резьбой                                                                 25.8

Штифт конический с резьбовой цапфой                                                                    25.9

Штифт пружинный                                                                                                                                              25.10

Штифт резьбовой с засверленным концом и шестигранным углублением под ключ                                                                                                                                     25.15

Штифт резьбовой с коническим притупленным концом и шестигранным углублением под ключ                                                                                                                                25.13

Штифт резьбовой с плоским концом и шестигранным углублением под ключ                                                                                                                                              25.12

Штифт резьбовой с плоским концом и шлицем                                                                                                                                              25.11

Штифт резьбовой с цилиндрическим концом и шестигранным углублением под ключ                                                                                                                                25.14

Штифт цилиндрический                                                                                               25.1

Штифт цилиндрический насеченный                                                                         25.4

Штифт цилиндрический насеченный с коническими насечками                           25.5

Штифт цилиндрический с внутренней резьбой                                                         25.2

Штифт цилиндрический с засверленными концами                                                 25.3

Шуруп с квадратной головкой                                                                                     21.2

Шуруп с полукруглой головкой                                                                                   21.3

Шуруп с полукруглой головкой и крестообразным шлицем                                    21.6

Шуруп с полупотайной головкой                                                                                 21.4

Шуруп с полупотайной головкой и крестообразным шлицем                                  21.7

Шуруп с потайной головкой                                                                                         21.5

Шуруп с потайной головкой и крестообразным шлицем                                          21.8

Шуруп с шестигранной головкой                                                                                 21.1

III. УКАЗАТЕЛЬ ТЕРМИНОВ И НАИМЕНОВАНИЙ КРЕПЕЖНЫХ ИЗДЕЛИЙ НА НЕМЕЦКОМ ЯЗЫКЕ

Gewinde                                                                                                                           1.1.

Kegliges (konisches) Gewinde                                                                                         1.2.

Blechschraubengewinde                                                                                                   1.3.

Holzschraubengewinde                                                                                                     1.4.

metrisches Gewinde                                                                                                         1.5.

metrisches Feingewinde                                                                                                   1.6.

Sechskantkopf                                                                                                                   2.1.

Sechskantkopf mit Telleransalz                                                                                        2.2.

Sechskantkopf mit Bund                                                                                                    2.3.

Sechskantkopf mit Flansch (Flanschkopf)                                                                         2.4.

Vierkantkopf                                                                                                                     2.5.

Vierkantkopf mit Bund                                                                                                      2.6.

Dreikantkopf mit Bund                                                                                                      2.7.

Achtkantkopf                                                                                                                     2.8.

Zwölfkantkopf mit Flansch                                                                                               2.9.

Hammerkopf                                                                                                                     2.10.

Hammerkopf mit Vierkantansatz                                                                                       2.11.

Halbrundkopf                                                                                                                    2.12.

Flachrundkopf                                                                                                                   2.13.

Halbrundkopf mit Nase                                                                                                     2.14.

Flachrundkopf mit Vierkantansatz                                                                                     2.15.

Halbrundkopf mit Ovalansatz                                                                                           2.16.

Zylinderkopf                                                                                                                     2.17.

Linsenzylinderkopf                                                                                                           2.18.

Linsenkopf                                                                                                                        2.19.

Flachkopf                                                                                                                          2.20.

Senkkopf                                                                                                                           2.21.

abgesetzter mit Senkkopf                                                                                                  2.22.

Senkkopf mit Nase                                                                                                            2.23.

Sekkopf mit Vierkantansatz                                                                                               2.24.

Linsensenkkopf                                                                                                                 2.25.

abgesetzter Linsensenkkopf                                                                                              2.26.

Rändelkopf                                                                                                                       2.27.

Kordelkopf                                                                                                                       2.28.

Dickschaft (Schaftdurchmesser = Gewindedurchmesser)                                                 3.1.

Dünnschaft (Schaftdurchmesser » Flankendurchmesser)                                                  3.2.

Paßschaft (Schaftdurchmesser > Gewindedurchmesser)                                                  3.3.

Dehnschaft (Schaftdurchmesser < Kerndurchmesser)                                                       3.4.

Ansatzschaft                                                                                                                      3.5.

Hohlschaft                                                                                                                        3.6.

Halbhohlschaft                                                                                                                  3.7.

ohne Kuppe                                                                                                                       4.1.

Linsenkuppe                                                                                                                      4.2.

Kegelkuppe                                                                                                                       4.3.

Spitze                                                                                                                                4.4.

Spitze, abgeflacht                                                                                                             4.5.

Ringschneide                                                                                                                    4.6.

Kegelstumpf                                                                                                                      4.7.

Zapfen                                                                                                                               4.8.

Kernansatz                                                                                                                        4.9.

Ansatzkuppe                                                                                                                     4.10.

Ansatzspitze, abgeflacht                                                                                                   4.11.

Schneidschraubenende mit Schabenut                                                                               4.12.

Blechschrauben - Spitze                                                                                                   4.13.

Blechschrauben - Zapfen                                                                                                  4.14.

Gewindeformendes Schraubenende                                                                                  4.15.

Spitze (Nagelbohrer)                                                                                                        4.16.

Sechskant                                                                                                                          5.1.

Vierkant                                                                                                                            5.2.

Dreikant                                                                                                                            5.3.

Achtkant                                                                                                                            5.4.

Zwölfkant                                                                                                                         5.5.

Innendreikant                                                                                                                    5.6.

Innenvierkant                                                                                                                    5.7.

Innensechskant                                                                                                                  5.8.

Innenkeilprofil                                                                                                                  5.9.

Innenzwölfzahn                                                                                                                 5.10.

gerader Schlitz                                                                                                                  5.11.

Kreuzschlitz                                                                                                                      5.12.

Flügel                                                                                                                               5.13.

Rändel                                                                                                                              5.14.

Kordel                                                                                                                              5.15.

Kreuzloch                                                                                                                         5.16.

Sechskantschraube                                                                                                            6.1.

Sechskant - Paßschraube                                                                                                  6.2.

Sechskantschraube mit Zapfen                                                                                          6.3.

Sechskantschrauhe mit Ansatzspitze                                                                                 6.4.

Sechskantschraube mit Dehnschaft                                                                                   6.5.

Sechskantschraube mit Bund                                                                                             6.6.

Sechskantschraube mit Flansch                                                                                         6.7.

Vierkantschraube                                                                                                              7.1.

Vierkantschrauhe mit Bund                                                                                               7.2.

Vierkantschraube mit Zapfen                                                                                            7.3.

Vierkantschraube mit Ringschneide                                                                                  7.4.

Vierkantschraube mit Bund und Ansatzkuppe                                                                   7.5.

Dreikantschraube                                                                                                              8.

Achtkantschraube                                                                                                              9.

Zwölfkantschraube mit Flansch                                                                                        10.

Hammerschraube                                                                                                              11.1.

Hammerschraube mit Vierkantansatz                                                                                11.2.

Hammerschraube mit Nase                                                                                               11.3.

Flachrundschraube mit Vierkantansatz                                                                              12.1.

Halbrundschraube mit Nase                                                                                              12.2.

Flachrundschraube mit Nase                                                                                             12.3.

Halbrundschraube mit Ovalansatz                                                                                    12.4.

Senkschraube mit Vierkantansatz                                                                                      13.1.

Senkschraube mit Nase                                                                                                     13.2.

Kegelsenkschraube                                                                                                           13.3.

Zylinderschraube mit Innensechskant                                                                                14.1.

Zylinderschraube mit Innensechskant und Ansatzschaft                                                    14.2.

Senkschrauben mit Innensechskant                                                                                    14.3.

Zylinderschraube mit Schlitz                                                                                            15.1.

Flachkopfschraube mit Schlitz                                                                                          15.2.

Linsenzylinderschraube mit Schlitz                                                                                  15.3.

Linsenzylinderschraube mit Schlitz und Zapfen                                                                15.4.

Linsenzylinderschraube mit Schlitz und Ansatz                                                                15.5.

Linsenzylinderschraube mit Schlitz und Kreuzloch                                                           15.6.

Linsenzylinderschraube mit Schlitz und kleinem Kopf                                                     15.7.

Senkschraube mit Schlitz                                                                                                  15.8.

Senkschraube mit Schlitz und Zapfen                                                                                15.9.

Linsensenkschraube mit Schlitz                                                                                                                                              15.10.

Linsensenkschraube mit Schlitz und Zapfen                                                                                                                                              15.11.

Senkschraube mit Halteschlitz                                                                                                                                              15.12.

Halbrundschraube mit Schlitz                                                                                                                                              15.13.

Linsenschraube mit Kreuzschlitz und Dehnschaft                                                             16.1.

Senkschraube mil Kreuzschlitz                                                                                         16.2.

Linsensenkschraube mit Kreuzschlitz                                                                               16.3.

Flachkopfschraube mit Kreuzschlitz                                                                                 16.4.

Sechskantschraube mit unverlierbarer Scheibe                                                                17.1.

Sechskantschraube mit unverlierbarem Federring und Scheibe                                        17.2.

Linsenzylinderschraube mit unverlierbarem Federring                                                     17.3.

Linsensenkschraube mit unverlierbarer Fächerscheibe                                                    17.4.

Augenschraube                                                                                                                 18.1.

Bogenklammerschraube                                                                                                    18.2.

Flachklammerschraube                                                                                                     18.3.

Tellerschraube mit Nasen                                                                                                 18.4.

Hakenschraube                                                                                                                 18.5.

Hutschraube                                                                                                                      18.6.

Kegelschraube                                                                                                                  18.7.

Steinschraube                                                                                                                   18.8.

Steinschraube                                                                                                                   18.9.

Flügelschraube                                                                                                                                              18.10.

Ringschraube                                                                                                                                              18.11.

Gewindestift mit Schlitz und Kegelstumpf                                                                        19.1.

Gewindestift mit Schlitz und Zapfen                                                                                 19.2.

Gewindestift mit Schlitz und Ringschneide                                                                      19.3.

Gewindestift mit Schlitz und Spitze                                                                                  19.4.

Gewindestift mit Innensechskant und Kegelstumpf                                                           19.5.

Gewindestift mit Innensechskant und Zapfen                                                                    19.6.

Gewindestift mit Innensechskant und Ringschneide                                                          19.7.

Gewindestifl mil Innensechskant und Spitze                                                                     19.8.

Sechskantblechschraube                                                                                                   20.1.

Zylinderblechschraube mit Schlitz                                                                                    20.2.

Senkblechschraube mit Schlitz                                                                                         20.3.

Linsensenkblechschraube mit Schlitz                                                                                20.4.

Senkblechschraube mit Kreuzschlitz                                                                                 20.5.

Linsensenkblechschraube mit Kreuzschlitz                                                                       20.6.

Flachkopf-Blechschraube mit Kreuzschlitz                                                                      20.7.

Sechskantholzschraube                                                                                                     21.1.

Vierkantholzschraube                                                                                                       21.2.

Halbrundholzschraube mit Schlitz                                                                                    21.3.

Linsensenkbolzschraube mit Schlitz                                                                                 21.4.

Senkholzschraube mit Schlitz                                                                                           21.5.

Halbrundholzschraube mit Kreuzschlitz                                                                           21.6.

Linsensenkholzschraube mit Kreuzschlitz                                                                         21.7.

Senkholzschraube mit Kreuzschlitz                                                                                   21.8.

Sechskant-Schneidschraube                                                                                              22.1.

Zylinder-Schneidschraube mit Schlitz                                                                              22.2.

Senk-Schneidschraube mit Schlitz                                                                                    22.3.

Linsensenk-Schneidschraube mit Schlitz                                                                          22.4.

Linsenzylinder-Schneidschraube mit Kreuzschlitz                                                            22.5.

Senk-Schneidschraube mit Kreuzschlitz                                                                           22.6.

Linsensenk-Schneidschraube mit Kreuzschlitz                                                                 22.7.

Sechskantschraube, gewindefurchend                                                                               23.

Rändelschraube                                                                                                                24.1.

Rändelschraube mit Spitze                                                                                               24.2.

Rändelschraube mit Ansatzspitze                                                                                     24.3.

Rändelschraube mit Ringschneide                                                                                    24.4.

Rändelschraube mit Linsenkuppe                                                                                     24.5.

Rändelschraube mit Zapfen                                                                                              24.6.

Zylinderstift                                                                                                                      25.1.

Zylinderstift mit Innengewinde                                                                                         25.2.

Nietstift                                                                                                                             25.3.

Zylinderkerbstift                                                                                                               25.4.

Kegelkerbstift                                                                                                                   25.5.

Kegelstift mit Spreizende                                                                                                 25.6.

Kegelstift                                                                                                                          25.7.

Kegelstift mit Innengewinde                                                                                             25.8.

Kegelstift mit Gewindezapfen                                                                                          25.9.

Spannstift                                                                                                                                              25.10.

Gewindestift mit Schlitz, Schaft und Kegelstumpf                                                                                                                                              25.11.

Gewindestift mit Innensechskant, Schaft und Kegelstumpf                                                                                                                                              25.12.

Gewindestift mit Innensechskant, Schaft und Spitze                                                                                                                                              25.13.

Gewindestift mit Innensechskant, Schaft und Zapfen                                                                                                                                              25.14.

Gewindestift mit Innensechskant, Schaft und Ringschneide                                                                                                                                              25.15.

Stiftschraube                                                                                                                     26.1.

Stiftschraube mit Dehnschaft                                                                                            26.2.

Gewindebolzen                                                                                                                 26.3.

Anschweißende                                                                                                                26.4.

Schraubenbolzen ohne Dehnschaft und Zapfen                                                                 26.5.

Halbrundniet                                                                                                                     27.1.

Flachrundniet                                                                                                                    27.2.

Senkniet                                                                                                                            27.3.

Linsenniet                                                                                                                         27.4.

flacher Linsenniet                                                                                                             27.5.

Flachkopfniet                                                                                                                    27.6.

Hohlniet mit Linsenkopf                                                                                                   27.7.

Hohlniet mit Flachkopf                                                                                                     27.8.

Hohlniet mit Senkkopf                                                                                                      27.9.

Halb-Hohlniet mit Flachkopf                                                                                                                                              27.10.

Halb-Hohlniet mit Senkkopf                                                                                                                                              27.11.

Halb-Hohlniet mit Halbrundkopf                                                                                                                                              27.12.

Sechskantmutter                                                                                                                28.1.

Flache Sechskantmutter                                                                                                    28.2.

Sechskantmutter mit Bund                                                                                                 28.3.

Sechskantmutter mit Flansch                                                                                             28.4.

Sechskantmutter mil Ansatz                                                                                              28.5.

Sechskant-Anschweißmutter                                                                                             28.6.

Vierkantmutter                                                                                                                  28.7.

Flache Vierkantmutter                                                                                                       28.8.

Ankermutter                                                                                                                      28.9.

Vierkantmutter mit Bund                                                                                                                                              28.10.

Vierkant-Anschweißmutter                                                                                                                                              28.11.

Dreikantmutter mit Bund                                                                                                                                              28.12.

Achtkantmutter                                                                                                                                              28.13.

Zwölfkantmutter mit Flansch                                                                                                                                              28.14.

Sechskantmutter mit Klemmteil, ganzmetallisch                                                                                                                                              28.15.

Sechskantmutter mit Klemmteil, mit nichtmetallischem Einsatz                                                                                                                                              28.16.

Kronenmutter                                                                                                                                              28.17.

Kronenmutter                                                                                                                                              28.18.

Flache Kronenmutter                                                                                                                                              28.19.

Hutmutter                                                                                                                                              28.20.

Rändelmutter                                                                                                                                              28.21.

Schlitzmutter                                                                                                                                              28.22.

Nutmutter                                                                                                                                              28.23.

Kreuzlochmutter                                                                                                                                              28.24.

Zweilochmulter                                                                                                                                              28.25.

Flügelmutter                                                                                                                                              28.26.

Scheibe                                                                                                                             29.1.

Vierkantscheibe                                                                                                                29.2.

Scheibe mit Vierkantloch                                                                                                  29.3.

Keilscheibe                                                                                                                      29.4.

Federring                                                                                                                          29.5.

Federring, aufgebogen                                                                                                      29.6.

Mehrfachfederring                                                                                                            29.7.

Federscheibe, gewölbt                                                                                                     29.8.

Fächerscheibe, außen gezahnt                                                                                           29.9.

Fächerscheibe, innen gezahnt                                                                                                                                              29.10.

Fächerscheibe, außen gezahnt, keglig                                                                                                                                              29.11.

Federscheibe, gewellt                                                                                                                                              29.12.

Zahnscheibe, innen gezahnt                                                                                                                                              29.13.

Zahnscheibe, außen gezahnt                                                                                                                                              29.14.

Zahnscheibe, außen gezahnt, keglig                                                                                                                                              29.15.

Sicherungsblech mit zwei Lappen                                                                                                                                              29.16.

Sicherungsblech mit Nase, außen                                                                                                                                              29.17.

Sicherungsblech mit Lappen                                                                                                                                              29.18.

Sicherungsblech mit Nase, innen                                                                                                                                              29.19.

Splint                                                                                                                                30.

IV. УКАЗАТЕЛЬ ТЕРМИНОВ И НАИМЕНОВАНИЙ КРЕПЕЖНЫХ ИЗДЕЛИЙ НА АНГЛИЙСКОМ ЯЗЫКЕ

Screw thread                                                                                                                    1.1.

Taper screw thread                                                                                                           1.2.

Tapping screw thread                                                                                                       1.3.

Wood screw thread                                                                                                          1.4.

Metric thread (SI)                                                                                                             1.5.

Metric fine pitch thread                                                                                                    1.6.

Hexagon head                                                                                                                   2.1.

Hexagon head with washer face                                                                                       2.2.

Hexagon head with collar                                                                                                 2.3.

Hexagon head with flange                                                                                                 2.4.

Square head                                                                                                                      2.5.

Square head with collar                                                                                                    2.6.

Triangle head with collar                                                                                                 2.7.

Octagonal head                                                                                                                 2.8.

12point flange head                                                                                                          2.9.

T-head                                                                                                                              2.10.

T-head with square neck                                                                                                   2.11.

Round head                                                                                                                       2.12.

Mushroom head                                                                                                                2.13.

Round head with nib                                                                                                         2.14.

Mushroom head with square neck                                                                                     2.15.

Round head with oval neck                                                                                               2.16.

Cheese head                                                                                                                      2.17.

Raised cheese head                                                                                                          2.18.

Binding head                                                                                                                     2.19.

Pan head                                                                                                                           2.20.

Countersunk head                                                                                                              2.21.

Undercut countersunk head                                                                                               2.22.

Countersunk head with nib                                                                                                2.23.

Countersunk head with square neck                                                                                  2.24.

Raised countersunk heart                                                                                                  2.25.

Undercut raised countersunk head                                                                                    2.26.

Straight knurled head                                                                                                        2.27.

Diamond knurled head                                                                                                      2.28.

Normal shank                                                                                                                    3.1.

Reduced shank                                                                                                                  3.2.

Increased shank                                                                                                                3.3.

Waisted shank                                                                                                                   3.4.

Shoulder                                                                                                                           3.5.

Tubular shank                                                                                                                   3.6.

Semi-tubular shank                                                                                                           3.7.

As-rolled end                                                                                                                   4.1.

Rounded end                                                                                                                     4.2.

Chamfered end                                                                                                                  4.3.

Cone point                                                                                                                        4.4.

Truncated cone point                                                                                                        4.5.

Cup point                                                                                                                          4.6.

Flat point                                                                                                                          4.7.

Long dog point                                                                                                                  4.8.

Short dog point                                                                                                                 4.9.

Short dog point with rounded end                                                                                     4.10.

Short dog point with truncated cone end                                                                           4.11.

Scrape point                                                                                                                     4.12.

4.14. End for self-tapping screw                                                                                      4.13.

End for thread rolling screw                                                                                             4.15.

Gimlet                                                                                                                               4.16.

Hexagon                                                                                                                            5.1.

Square                                                                                                                              5.2.

Triangle                                                                                                                            5.3.

Octagon                                                                                                                            5.4.

12point                                                                                                                             5.5.

Triangle                                                                                                                            5.6.

Square socket                                                                                                                   5.7.

Hexagon socket                                                                                                                 5.8.

Six-spline socket                                                                                                              5.9.

12point socket                                                                                                                  5.10.

Slot                                                                                                                                   5.11.

Cross recess                                                                                                                     5.12.

Wing                                                                                                                                 5.13.

Straight knurl                                                                                                                    5.14.

Diamond knurl                                                                                                                  5.15.

Cross hole                                                                                                                        5.16.

Hexagon holt                                                                                                                     6.1.

Hexagon fit bolt                                                                                                                6.2.

Hexagon set screw with full dog point                                                                             6.3.

Hexagon set screw with half dog point and flat cone point                                               6.4.

Hexagon screw with waisted shank                                                                                  6.5.

Hexagon bolt with collar                                                                                                  6.6.

Hexagon bolt with flange                                                                                                  6.7.

Square head bolt                                                                                                               7.1.

Square head bolt with collar                                                                                            7.2.

Square set screw with half dog point                                                                                7.3.

Square set screw with cup point                                                                                       7.4.

Square set screw with collar and half dog point with rounded end                                  7.5.

Triangle head bolt with collar                                                                                          8.

Octagon bolt                                                                                                                     9.

12point flange screw                                                                                                        10.

T-head bolt                                                                                                                       11.1.

T-head bolt with square neck                                                                                           11.2.

T-head bolt with double nib                                                                                             11.3.

Mushroom head square neck bolt                                                                                     12.1.

Cup head nib bolt                                                                                                             12.2.

Mushroom head nib bolt                                                                                                   12.3.

Cup oval neck bolt                                                                                                            12.4.

Flat countersunk square neck bolt                                                                                     13.1.

Flat countersunk nib bolt                                                                                                  13.2.

Deep flat countersunk bolt                                                                                                13.3.

Hexagon socket head cap screw                                                                                       14.1.

Hexagon socket head shoulder screw                                                                               14.2.

Hexagon socket countersunk cap head screw                                                                   14.3.

Slotted cheese head screw                                                                                                15.1.

Slotted pan head screw                                                                                                     15.2.

Slotted raised cheese head screw                                                                                     15.3.

Slotted raised cheese head screw with full dog point                                                       15.4.

Slotted raised cheese head fit bolt                                                                                    15.5.

Slotted capstan screw                                                                                                       15.6.

Slotted small raised cheese head screw                                                                           15.7.

Slotted countersunk head screw                                                                                        15.8.

Slotted countersunk head screw with full dog point                                                         15.9.

Slotted raised countersunk head screw                                                                                                                                              15.10.

Slotted raised countersunk head screw with full dog point                                                                                                                                              15.11.

Countersunk head screw with forgel slot                                                                                                                                              15.12.

Slotted round head screw                                                                                                                                              15.13.

Cross recessed raised cheese head screw                                                                        16.1.

Cross recessed countersunk head screw                                                                           16.2.

Cross recessed raised countersunk head screw                                                                16.3.

Cross recessed pan head screw                                                                                        16.4.

Hexagon screw with captive plain washer                                                                       17.1.

Hexagon screw with captive spring and plain washer                                                      17.2.

Raised cheese head screw with captive spring washer                                                    17.3.

Raised countersunk head screw with captive countersunk serrated lock washer              17.4.

Eye bolt                                                                                                                            18.1.

Mushroom head anchor bolt                                                                                             18.2.

Flat head anchor bolt                                                                                                        18.3.

Belting bolt                                                                                                                       18.4.

Clip bolt                                                                                                                           18.5.

Acorn hexagon head bolt                                                                                                  18.6.

Conical bolt                                                                                                                      18.7.

Masonry bolt                                                                                                                    18.8.

Foundation bolt                                                                                                                 18.9.

Wing screw                                                                                                                                              18.10.

Lifting eye bolt                                                                                                                                              18.11.

Slotted set screw with flat point                                                                                       19.1.

Slotted set screw with full dog point                                                                                19.2.

Slotted set screw with cup point                                                                                       19.3.

Slotted set screw with cone point                                                                                     19.4.

Hexagon socket set screw with flat point                                                                         19.5.

Hexagon socket set screw with full dog point                                                                  19.6.

Hexagon socket screw with cup point                                                                              19.7.

Hexagon socket set screw with cone point                                                                       19.8.

Hexagon head tapping screw                                                                                            20.1.

Slotted pan head tapping screw                                                                                        20.2.

Slotted countersunk head tapping screw                                                                           20.3.

Slotted raised countersunk head tapping screw                                                                20.4.

Cross recessed countersunk head tapping screw                                                              20.5.

Cross recessed raised countersunk head tapping screw                                                   20.6.

Cross recessed pan head tapping screw                                                                           20.7.

Hexagon head wood screw                                                                                               21.1.

Square head wood screw                                                                                                 21.2.

Slotted round head wood screw                                                                                       21.3.

Slotted raised countersunk head wood screw                                                                   21.4.

Slotted countersunk head wood screw                                                                              21.5.

Cross recessed pan head wood screw                                                                              21.6.

Cross recessed raised countersunk head wood screw                                                      21.7.

Cross recessed countersunk head wood screw                                                                 21.8.

Hexagon head thread cutting screw                                                                                  22.1.

Slotted cheese head thread cutting screw                                                                         22.2.

Slotted countersunk head thread cutting screw                                                                 22.3.

Slotted raised countersunk head thread cutting screw                                                       22.4.

Cross recessed pan head thread cutting screw                                                                  22.5.

Cross recessed countersunk head thread cutting screw                                                     22.6.

Cross recessed raised countersunk head thread cutting screw                                          22.7.

Hexagon head thread forming screw                                                                                 23.

Straight knurled head screw                                                                                             24.1.

Straight knurled head screw with cone point                                                                    24.2.

Straight knurled head screw with short dog point with truncated cone end                      24.3.

Straight knurled head screw with cup point                                                                      24.4.

Straight knurled head screw with rounded point                                                               24.5.

Straight knurled head screw with full dog point                                                               24.6.

Cylindrical pin                                                                                                                 25.1.

Cylindrical pin with internal thread                                                                                  25.2.

Cylindrical pin with cup points                                                                                        25.3.

Cylindrical notched pin                                                                                                    25.4.

Cylindrical notched pin with conical notches                                                                   25.5.

Tension taper pin                                                                                                              25.6.

Taper pin                                                                                                                          25.7.

Taper pin with internal thread                                                                                          25.8.

Taper pin with threaded stem                                                                                           25.9.

Spring type straight pin                                                                                                                                              25.10.

Slotted headless screw with flat chamfered end                                                                                                                                              25.11.

Hexagon socket headless screw with flat chamfered end                                                                                                                                              25.12.

Hexagon socket headless screw with truncated cone point                                                                                                                                              25.13.

Hexagon socket headless screw with full dog point                                                                                                                                              25.14.

Hexagon socket headless screw with cup point                                                                                                                                              25.15.

Stud                                                                                                                                  26.1.

Waisted stud                                                                                                                     26.2.

Stud bolt                                                                                                                           26.3.

Weld stud                                                                                                                         26.4.

Double end stud with full shank                                                                                        26.5.

Round head rivet                                                                                                              27.1.

Mushroom head rivet                                                                                                        27.2.

Countersunk head rivet                                                                                                     27.3.

Raised countersunk head rivet                                                                                          27.4.

Shallow raised countersunk head rivet                                                                             27.5.

Flat head rivet                                                                                                                  27.6.

Round head hollow rivet                                                                                                  27.7.

Flat head hollow rivet                                                                                                      27.8.

Countersunk head hollow rivet                                                                                         27.9.

Flat head semi-hollow rivet                                                                                                                                              27.10.

Countersunk head semi-hollow rivet                                                                                                                                              27.11.

Round head semi-hollow rivet                                                                                                                                              27.12.

Hexagon nut                                                                                                                      28.1.

Hexagon thin nut                                                                                                               28.2.

Hexagon nut with collar                                                                                                    28.3.

Hexagon nut with flange                                                                                                   28.4.

Washer faced hexagon nut                                                                                                28.5.

Hexagon weld nut                                                                                                             28.6.

Square nut                                                                                                                         28.7.

Square thin nut without chamfer                                                                                        28.8.

Foundation nut                                                                                                                  28.9.

Square nut with collar                                                                                                                                              28.10.

Square weld nut                                                                                                                                              28.11.

Triangle nut with collar                                                                                                                                              28.12.

Octagon nut                                                                                                                                              28.13.

12point flange nut                                                                                                                                              28.14.

Prevailing torque type hexagon nut with deformed thread                                                                                                                                              28.15.

Prevailing torque type hexagon nut with ring polymer insert                                                                                                                                              28.16.

Hexagon slotted nut                                                                                                                                              28.17.

Hexagon castle nut                                                                                                                                              28.18.

Hexagon thin castle nut                                                                                                                                              28.19.

Acorn nut                                                                                                                                              28.20.

Knurled nut                                                                                                                                              28.21.

Slotted round nut                                                                                                                                              28.22.

Slotted round nut for hook-spanner                                                                                                                                              28.23.

Round nut with set pin holes in side                                                                                                                                              28.24.

Round nut with drilled holes in one face                                                                                                                                              28.25.

Wing nut                                                                                                                                              28.26.

Plain washer                                                                                                                     29.1.

Square washer with round hole                                                                                        29.2.

Round washer with square hole                                                                                        29.3.

Square taper washer                                                                                                         29.4.

Single coil spring lock washer with square ends                                                              29.5.

Single coil spring lock washer with tang ends                                                                  29.6.

Double coil spring lock washer                                                                                        29.7.

Curvet spring washer                                                                                                        29.8.

Serrated lock washer external teeth                                                                                  29.9.

Serrated lock washer internal teeth                                                                                                                                              29.10.

Countersunk serrated external toothed lock washer                                                                                                                                              29.11.

Wave spring washer                                                                                                                                              29.12.

Lock washer external teeth                                                                                                                                              29.13.

Lock washer internal teeth                                                                                                                                              29.14.

Countersunk external toothed lock washer                                                                                                                                              29.15.

Tab washer with long tab and wing                                                                                                                                              29.16.

External tab washer                                                                                                                                              29.17.

Tab washer with long tab                                                                                                                                              29.18.

Internal tab washer                                                                                                                                              29.19.

Split pin                                                                                                                            30 .

V. УКАЗАТЕЛЬ ТЕРМИНОВ И НАИМЕНОВАНИЙ КРЕПЕЖНЫХ ИЗДЕЛИЙ НА ФРАНЦУЗСКОМ ЯЗЫКЕ

Filetage cylindrique                                                                                                          1.1.

Filetage conique                                                                                                               1.2.

Filetage de vis à tôle                                                                                                        1.3.

Filetage de vis à bois                                                                                                       1.4.

Filetage métrique (SI)                                                                                                       1.5.

Filetage métrique à pas fin                                                                                               1.6.

Tête hexagonale                                                                                                                2.1.

Tête hexagonale à collerette                                                                                             2.2.

Tête hexagonale à embase cylindrique                                                                             2.3.

Tête hexagonale à embase cylindro-tronconique                                                              2.4.

Tête carr é e                                                                                                                       2.5.

Tête carrée à embase cylindrique                                                                                     2.6.

Tête triangulaire à embase cylindrique                                                                             2.7.

Tête octogonale                                                                                                                2.8.

Tête binexagonale                                                                                                             2.9.

Tête rectangulaire à angles abattus                                                                                   2.10.

Tête rectangulaire à angles abattus à collet carré                                                             2.11.

Tête ronde                                                                                                                        2.12.

Tête bombée                                                                                                                     2.13.

Tête ronde à ergot                                                                                                             2.14.

Tête bombée à collet carré                                                                                               2.15.

Tête ronde a collet carré large                                                                                         2.16.

Tête cylindrique                                                                                                               2.17.

2.19. Tête cylindrique bombée                                                                                         2.18.

Tête cylindrique à dépouille                                                                                             2.20.

Tête fraisée                                                                                                                       2.21.

Tête fraisée à épaulement                                                                                                 2.22.

Tête fraisée à ergot                                                                                                           2.23.

Tête fraisée à collet carré                                                                                                 2.24.

Tête fraisée bombée                                                                                                         2.25.

Tête fraisée bombée à épaulement                                                                                    2.26.

Tête cylindrique moletée                                                                                                  2.27.

Tête moletée croisé                                                                                                          2.28.

Tige normale                                                                                                                    3.1.

Tige réduite                                                                                                                      3.2.

Tige ajustable                                                                                                                   3.3.

Tige allégeé                                                                                                                      3.4.

Tige ajustable à bout fileté réduit                                                                                     3.5.

Tige tubulaire                                                                                                                   3.6.

Tige demi-tubulaire                                                                                                          3.7.

Bout plat                                                                                                                           4.1.

Bout bombé                                                                                                                      4.2.

Bout chanfreiné                                                                                                                 4.3.

Bout pointu                                                                                                                       4.4.

Bout pilote                                                                                                                        4.5.

Cuvette                                                                                                                             4.6.

Bout chanfreiné                                                                                                                 4.7.

Téton long                                                                                                                         4.8.

Т éton court                                                                                                                       4.9.

Téton court bombé                                                                                                            4.10.

Téton tronconique                                                                                                             4.11.

Bout tronconique de vis à tôle                                                                                          4.12.

Bout pointu de vis à tôle                                                                                                   4.13.

Bout plat de vis à tôle                                                                                                       4.14.

Bout de vis auto-taraudeuse par déformation de matière                                                  4.15.

Foret                                                                                                                                 4.16.

Hexagonal                                                                                                                         5.1.

Carré                                                                                                                                5.2.

Triangulaire                                                                                                                      5.3.

Oclogonal                                                                                                                         5.4.

Bihexagonal                                                                                                                      5.5.

Triangle creux                                                                                                                  5.6.

Carré creux                                                                                                                       5.7.

Six pans creux                                                                                                                  5.8.

Empreinte six cannelures                                                                                                  5.9.

Empreinte bihexagonale                                                                                                   5.10.

Fente                                                                                                                                 5.11.

Empreinte cruciforme                                                                                                       5.12.

Oreilles                                                                                                                            5.13.

Moleté                                                                                                                              5.14.

Moleté croisé                                                                                                                   5.15.

Percage en croix                                                                                                               5.16.

Vis à tête hexagonale                                                                                                        6.1.

Corps de boulon ajustable à tête hexagonale avec gorge de dégagement                          6.2.

Vis à tête hexagonale à téton avec gorge de digagement                                                   6.3.

Vis à tête hexagonale, à téton cylindro-tronconique                                                         6.4.

Vis à tete hexagonale à tige allégée                                                                                  6.5.

Vis à tête hexagonale à embase cylindrique                                                                     6.6.

Vis à tête hexagonale à embase cylindlro-tronconique                                                     6.7.

Vis à tête carrée                                                                                                                7.1.

Vis à tête carrée à embase cylindrique                                                                             7.2.

Vis à tête carrée à teton court                                                                                           7.3.

Vis à tête carrée à cuvette                                                                                                 7.4.

Vis à tête carrée à embase cylindrique à teton count                                                        7.5.

Vis à tête triangulaire à embase cylindrique                                                                     8.

Vis à tête octogonale                                                                                                        9.

Vis à tête bihexagonal                                                                                                       10.

Vis à tête rectangulaire à angles abattus                                                                           11.1.

Vis à tête rectangulaire à angles abattus à collet carré                                                     11.2.

Vis à tête rectangulaire à angles abattus à deux ergots                                                     11.3.

Corps de boulon à tête bombée aplatie, à collet carré                                                      12.1.

Corps de boulon à tête ronde, à ergot                                                                               12.2.

Corps de boulon à tête bombee, à ergot                                                                            12.3.

Corps de boulon à tête rondo, à collet carré large                                                            12.4.

Corps de boulon à tête fraisée, à collet carré                                                                   13.1.

Corps de boulon à tête fraisee, à ergot                                                                             13.2.

Corps de boulon de roue                                                                                                  13.3.

Vis à tête cylindrique a six pans creux                                                                             14.1.

Vis ajustable à tête cylindrique a six pans creux et à bout fileté réduite                           14.2.

Vis à tête fraisée à six pans creux                                                                                     14.3.

Vis à tête cylindrique fendue                                                                                            15.1.

Vis à tête cylindrique à depouille fendue                                                                         15.2.

Vis à tête cylindrique bombée large fendue                                                                      15.3.

Vis à tête cylindrique bombée mince fendue, à téton                                                        15.4.

Vis à tête cylindrique bombée mince fendue, à tige ajustable                                           15.5.

Vis à tête cylindrique bombée fendue avec percage en croix                                           15.6.

Vis à tête cylindrique bombée réduite fendue                                                                   15.7.

Vis à tête fraisée fendue                                                                                                   15.8.

Vis à tête fraisée fendue, à téton                                                                                       15.9.

Vis à tête fraisée bombée fendue                                                                                                                                              15.10.

Vis à tête fraisée bombée fendue, à téton                                                                                                                                              15.11.

Vis à tête fraisée à empreinte rectangulaife ou à fente forgée                                                                                                                                              15.12.

Vis à tête ronde fendue                                                                                                                                              15.13.

Vis à tête cylindrique bombée à empreinte cruciforme                                                     16.1.

Vis à tête fraisée à empreinte cruciforme                                                                         16.2.

Vis à tête fraisée bombée à empreinte cruciforme                                                            16.3.

Vis à tête cylindrique à dépouille à empreinte cruciforme                                               16.4.

Vis à tête hexagonale à rondelle cylindrique plate incorporée                                         17.1.

Vis à tête hexagonale à rondelles (élastique et cylindrique plate) incorporées                17.2.

Vis à tête cylindrique bombée, à rondelle élastique incorporée                                       17.3.

Vis à tête fraisée bombée fendue, à rondelee à dents extérieures, concave, incorporée   17.4.

Corps de boulon à oeil                                                                                                     18.1.

Corps de boulon à t ê te bombée à agrafe (1 ou 2)                                                             18.2.

Corps de boulon à t ê te plate à agrafe (1 ou 2)                                                                  18.3.

Corps de boulon de courroie                                                                                            18.4.

Crampon fileté                                                                                                                  18.5.

Vis à t ê te hexagonale à calotte                                                                                          18.6.

Vis conique                                                                                                                       18.7.

Tige de scellement à queue de carpe                                                                                18.8.

Tige de scellement                                                                                                            18.9.

Vis à oreilles                                                                                                                                              18.10.

Vis à anneau                                                                                                                                              18.11 .

Vis sans t ê te, fendue, entiérement filetée, à bout chanfreiné                                             19.1.

Vis sans t ê te, fendue, entiérement filetée, à téton                                                              19.2.

Vis sans t ê te, fendue, entiérement filetée, à cuvette                                                          19.3.

Vis sans t ê te, fendue, entiérement filetée, à bout pointu                                                    19.4.

Vis sans t ê te, à six pans creux, entierement filetée, à bout chanfreiné                              19.5.

Vis sans t ê te, à six pans creux, entierement filetée, à téton                                               19.6.

Vis sans t ê te, à six pans crciix, entierement filelée, à cuvette                                          19.7.

Vis sans t ê te, à six pans creux, entierement filutée, à bout pointu                                     19.8.

Vis à tôle à t ê te hexagonale, à bout pointu; à bout plat                                                     20.1.

Vis à tôle à t ê te cylindrique à depouille fendue, à bout pointu; à bout plat                       20.2.

Vis à tôle à t ê te fraisée fendue, à bout pointu; à bout plat                                                 20.3.

Vis à tôle à t ê te fraisée bombée fendue, à bout pointu; à bout plat                                   20.4.

Vis à tôle à t ê te fraisée à empreinte cruciforme, à bout pointu; à bout plat                      20.5.

Vis à tôle à t ê te fraisée bombée à empreinte cruciforme, à bout pointu; à bout plat         20.6.

Vis à tôle à t ê te cylindrique à depouille à empreinte cruciforme, à bout pointu; à bout plat                                                                                                                                              20.7.

Vis à bois à t ê te hexagonale                                                                                             21.1.

Vis à bois à t ê te carrée                                                                                                     21.2.

Vis à bois à t ê te ronde fendue                                                                                           21.3.

Vis à bois à t ê te fraisée bombée fendue                                                                           21.4.

Vis à bois à t ê te fraisée fendue                                                                                         21.5.

Vis à bois à t ê te ronde à empreinte cruciforme                                                                21.6.

Vis à bois à t ê te fraisée bombée à empreinte cruciforme                                                 21.7.

Vis à bois à t ê te fraisée à empreinte cruciforme                                                               21.8.

Vis auto-taraudeuse à t ê te hexagonale                                                                              22.1.

Vis auto-taraudeuse à t ê te cylindrique fendue                                                                  22.2.

Vis auto-taraudeuse à t ê te fraisfée fendue                                                                        22.3.

Vis auto-taraudeuse à t ê te fraisée bombée fendue                                                            22.4.

Vis auto-taraudeuse à t ê te cylindrique à dépouille à empreinte cruciforme                     22.5.

Vis auto-taraudeuse à t ê te fraisée à empreinte cruciforme                                               22.6.

Vis auto-taraudeuse à t ê te fraisée bombée à empreinte cruciforme                                  22.7.

Vis auto-taraudeus par deformation de matiére                                                                23.

Vis à t ê te cylindrique moletée                                                                                          24.1.

Vis à t ê te cylindrique moletée, à bout pointu                                                                    24.2.

Vis à t ê te cylindrique moletée à téton cylindro-tronconique                                             24.3.

Vis à t ê te cylindrique moletée à cuvette                                                                           24.4.

Vis à t ê te cylindrique moletée à bout bombée                                                                  24.5.

Vis à t ê te cylindrique moletée à téton long                                                                       24.6.

Goupille cylindrique                                                                                                        25.1.

Goupille cylindrique à filet femelle                                                                                 25.2.

Goupille cylindrique à cuvette                                                                                         25.3.

Goupille cylindrique à taille                                                                                            25.4.

Goupille cylindrique à tailles coniques                                                                            25.5.

Goupille conique fendue                                                                                                   25.6.

Goupille cunique                                                                                                              25.7.

Goupille conique à filet femelle                                                                                       25.8.

Goupille conique à tourillon fileté                                                                                   25.9.

Goupille elastique                                                                                                                                              25.10.

Vis sans tête fendue, partiellement filetée, à bout chanfreiné                                                                                                                                              25.11.

Vis sans tête à six pans creux, partiellement, filetée, à bout chanfreiné                                                                                                                                              25.12.

Vis sans tête à six pans creux, partiellement filetée, à bout pointu                                                                                                                                              25.13.

Vis sans tête à six pans creux, partiellement filetée, à téton                                                                                                                                              25.14.

Vis sans tête à six pans creux, partiellement filetée, à cuvette                                                                                                                                              25.15.

Goujon                                                                                                                              26.1.

Goujon à corps allégé                                                                                                       26.2.

Tige filetée                                                                                                                       26.3.

Tige à sounde                                                                                                                   26.4.

Goujon à deux gorges de dégagement et à téton                                                                26.5.

Rivet à tête ronde                                                                                                             27.1.

Rivet à tête bombée                                                                                                          27.2.

Rivet à tête fraisée                                                                                                            27.3.

Rivet à tête fraisée bombée                                                                                              27.4.

Rivet à tête fraisée bombée bas                                                                                        27.5.

Rivet à tête plate                                                                                                               27.6.

Rivet cretix à tête ronde                                                                                                   27.7.

Rivet creux à tête plate                                                                                                     27.8.

Rivet creux à tête fraisée                                                                                                  27.9.

Rivet semi-creux à tête plate                                                                                                                                              27.10.

Rivet semi-crcux à tête fraisée                                                                                                                                              27.11.

Rivet semi-creux à tête ronde                                                                                                                                              27.12.

Ecrou hexagonal                                                                                                               28.1.

Ecrou hexagonal bas                                                                                                         28.2.

Ecrou hexagonal à embase cylindrique                                                                             28.3.

Ecrou hexagonal à embase cylindro-tronconique                                                             28.4.

Ecrou hexagonal à collerette                                                                                            28.5.

Ecrou hexagonal à souder                                                                                                 28.6.

Ecrou carré                                                                                                                       28.7.

Ecrou carre bas                                                                                                                28.8.

Ecrou de tige d’ancrage                                                                                                    28.9.

Ecrou carré à embase cylindrique                                                                                                                                              28.10.

Ecrou carré à souder                                                                                                                                              28.11.

Ecrou triangulaire à embase cylindrique                                                                                                                                              28.12.

Ecrou octogonal                                                                                                                                              28.13.

Ecrou bihexagonal                                                                                                                                              28.14.

Ecrou auto-freiné hexagonal à filet déformé                                                                                                                                              28.15.

Ecrou auto-freiné hexagonal anneau polimére                                                                                                                                              28.16.

Ecrou hexagonal à créneaux                                                                                                                                              28.17.

Ecrou hexagonal à créneaux dégagés                                                                                                                                              28.18.

Ecrou hexagonal bas à creneaux dégagés                                                                                                                                              28.19.

Ecrou borgne à calotte                                                                                                                                              28.20.

Ecrou moleté                                                                                                                                              28.21.

28.23. Ecrou cylindrique à fente                                                                                                                                              28.22.

Ecrou cylindrique à trous percés en croix                                                                                                                                              28.24.

Ecrou cylindrique à deux trous percés sur une fase                                                                                                                                              28.25.

Ecrou à oreilles                                                                                                                                              28.26.

Rondelle plats                                                                                                                  29.1.

Plaquette carrée                                                                                                                29.2.

Rondelle plate à trou carrée                                                                                             29.3.

Plaquette oblique                                                                                                              29.4.

Rondelle élastique simple spire sans becs                                                                       29.5.

Rondelle élastique simple spire abes becs                                                                       29.6.

Rondelle élastique double spire sans becs                                                                       29.7.

Rondelle élastique cintrée                                                                                                29.8.

Rondelle élastique plane à dents chevauchantes extérieures                                            29.9.

Rondelle élastique plane à dents chevauchantes intérieures                                                                                                                                              29.10.

Rondelle élastique concave à dents chevauchantes extérieures                                                                                                                                              29.11.

Rondelle élastique ondulée                                                                                                                                              29.12.

Rondelle élastique plane à dents espacées extérieures                                                                                                                                              29.13.

Rondelle élastique plane à dents espacées intérieures                                                                                                                                              29.14.

Rondelle élasllque concave à dents espacées extérieures                                                                                                                                              29.15.

Frein d’ecrou d’equerre à aileron                                                                                                                                              29.16.

Rondelle frein d’ecrou à ergot extérieur                                                                                                                                              29.17.

Frein d’ecrou droit à aileron                                                                                                                                              29.18.

Rondelle frein d’ecrou à ergot intérieur                                                                                                                                              29.19.

Goupille cylirndrique fendue                                                                                            30.

ИНФОРМАЦИОННЫЕ ДАННЫЕ

1. РАЗРАБОТАН И ВНЕСЕН Министерством черной металлургии СССР

РАЗРАБОТЧИКИ

Б.М. Ригмант; Т.Е. Юрченко

2. УТВЕРЖДЕН И ВВЕДЕН В ДЕЙСТВИЕ Постановлением Государственного комитета СССР по стандартам от 30.09.86 № 2941

3. Срок проверки 2000 г., периодичность проверки - 10 лет

4. Стандарт полностью соответствует стандарту СТ СЭВ 6300-88

5. Стандарт полностью соответствует международному стандарту ИСО 1891-79

6. ВВЕДЕН ВПЕРВЫЕ

7. ССЫЛОЧНЫЕ НОРМАТИВНО-ТЕХНИЧЕСКИЕ ДОКУМЕНТЫ

Обозначение НТД, на который дана ссылка

Номер пункта

ГОСТ 11708-82

Вводная часть

8. ПЕРЕИЗДАНИЕ март 1990 г. с Изменением № 1, утвержденным в июне 1989 (ИУС 11-89)

СОДЕРЖАНИЕ

Алфавитный указатель терминов на русском языке . 4

Алфавитный указатель терминов на немецком языке . 5

Алфавитный указатель терминов на английском языке . 5

Алфавитный указатель терминов на французском языке . 6

Приложение Терминология и номенклатура крепежных изделий на русском, немецком, английском и французском языках . 6

I. Терминология и номенклатура крепежных изделий . 6

1. Резьба . 6

2. Формы головок . 7

3. Формы стержней . 9

4. Концы болтов и винтов . 10

5. Элементы, передающие вращение . 11

6. Болты и винты с шестигранной головкой . 12

7. Винты с четырехгранной (квадратной) головкой . 13

8. Болты с трехгранной головкой . 13

9. Болты с восьмигранной головкой . 13

10. Болты с двенадцатигранной головкой . 13

11. Болты с т-образной головкой . 13

12. Болты с полукруглой головкой . 14

13. Болты с потайными головками . 14

14. Винты с внутренним шестигранником .. 14

15. Винты с прямым шлицем .. 14

16. Винты с крестообразным шлицем .. 15

17. Винты с невыпадающими деталями . 15

18. Различные типы болтов и винтов . 16

19. Установочные винты без головок . 17

20. Самонарезающие винты .. 17

21. Шурупы .. 17

22. Резьбонарезающие винты .. 18

23. Резьбовыдавливающие винты .. 18

24. Винты с рифленой головкой . 18

25. Штифты .. 19

26. Шпильки . 20

27. Заклепки . 20

28. Гайки . 21

29. Шайбы .. 23

30. Шплинты .. 25

II. Алфавитный указатель терминов и наименований крепежных изделий на русском языке . 25

III. Указатель терминов и наименований крепежных изделий на немецком языке . 31

IV. Указатель терминов и наименований крепежных изделий на английском языке . 36

V. Указатель терминов и наименований крепежных изделий на французском языке . 42

Еще документы скачать бесплатно